A failure in the vehicle’s emissions, ignition, gasoline, or exhaust systems is what causes a check engine light to switch on. You’ve just started driving around in your GMC Sierra when suddenly the car flashes a coded warning that there might be an internal issue that needs to be reset. But not everyone knows How to Reset Check Engine Light On GMC Sierra.
Generally speaking, we reset by driving continuously, switching the ignition both on and off, unplugging the battery, monitoring the gas tank cap, attempting to spin the steering wheel, and fixing the mass airflow sensor, O2 sensor, converter, vacuum leakage, or plug. Or if you can’t, take it to the auto shop to be serviced.
We would like to highlight the possible signs that trigger resetting the check engine light. Hopefully, you won’t leave the site without having your solution.
Contents
- 1 Why Check Engine Light Comes On?
- 2 Check Engine Light on GMC Sierra 1500 Codes
- 3 How to Reset Check Engine Light On GMC Sierra – Steps to Follow
- 3.1 4 Common Signs That Ensure GMC Sierra Reset
- 3.2 Reset Check Engine Light on GMC Sierra – Manual 6 Steps
- 3.3 Start Your Engine
- 3.4 Continue Driving
- 3.5 Turn the Ignition On and Off
- 3.6 Attempt Steering Wheel
- 3.7 Disconnect Battery
- 3.8 Monitoring the Gas Tank Lid
- 3.9 Remove the Plug
- 3.10 Visit Service Center
- 4 Frequently Asked Questions
- 5 Final Words
Why Check Engine Light Comes On?
The check engine light is one of the advanced technologies found in today’s vehicles, which detects issues and signals them when the ignition system isn’t working efficiently. You can also say, the on-board monitoring system’s strategy is to notify you if anything is wrong internally.
The system maintains a “trouble code” that indicates the trouble that needs to be fixed when the light turns on. In United States law, check engine lights are required to help the driver to be safe by alarming them by flashing lights of potential issues.
Check Engine Light on GMC Sierra 1500 Codes
It’s usually not a wise choice to drive with the check engine light flashing. Remember, this technology will flash some codes that must be valued. When the blinking light appears frequently, the engine is misfiring severely, enabling unburned gasoline to escape into the exhaust system, which is the most common cause. However, let’s look at the typical problems and different codes that the Check Engine Light (CEL) indicates on the GMC Sierra.
- Circuit board problems
- Difficulty with the emission controls
- Problems in the ignition system
- Misfire in the engine
- Long used battery
- Transmission difficulties
- Defective or loose gas cap
- Pressure sensor for the fuel tank
- Corroded fuel injectors
- RPMs quickly rise
- Rusty spark plugs
- Malfunctioning catalytic converter
- The airflow sensor is dirty
- Broken thermostat
- An O2 sensor fault.
How to Reset Check Engine Light On GMC Sierra – Steps to Follow
At a certain moment, we riders notice the check engine light on GMC Sierra flashing. But we lack the knowledge of resetting. So, how to fix check engine light? What could be the simple trick to turn off check engine light? Everything will be resolved below!
4 Common Signs That Ensure GMC Sierra Reset
The check engine light often illuminates, notifying us by showing certain codes. However, the following are the primary triggers for your car:
- Difficulty starting the car.
- Another indicator to reset is harsh idling.
- Smoke emerging from the vehicle’s tailpipe signals that the system requires a reset.
- Also, fuel sensor trouble ensures resetting.
Reset Check Engine Light on GMC Sierra – Manual 6 Steps
An immediate repair or reset is actually necessary for an illuminated engine light since it might trigger major issues inside your car. You have some easy ways to reset your GMC Sierra engine light manually. If you are in hurry try these simple steps:
- First, turn the ignition switch off.
- Wear gloves and protective goggles.
- Find the negative terminal that has a black cap and the minus sign (-). Unlike the positive terminal, which is marked with a red cap and a plus sign (+).
- Now, remove the negative connector from the Sierras battery, then use a wrench to loosen the nut.
- Take around 30 to 60 seconds and keep it aside.
- After that, use your wrench to firmly tighten the negative cable connection by reconnecting it.
RELATED: How to bypass Chevy ignition switch
Start Your Engine
Do you know? The vacuum is used to open and stop the exhaust gas recirculation (EGR) valve on the GMC Sierra. However, start the engine of your car. Problematic valve not performing properly aim to point out the check engine light.
Continue Driving
When the check engine light comes on while you are driving the Sierra, you don’t have to stop the vehicle. Drive through the light as it comes on because it can be a minor problem that doesn’t require immediate attention.
Turn the Ignition On and Off
You might need to turn the car on for a brief period of time before turning it off when the engine light is blinking. It’s a restart technique that could clear the error codes and also turn off the light. You need to restart two or three times occasionally.
Attempt Steering Wheel
You will need to turn off the ignition before making sure you’re using the steering wheel to drive. You will require left and right turns on the steering wheel. Ensure the pressure in the power steering system is released.
Disconnect Battery
Your car’s performance may begin to decline when the battery is old and worn out. As a result, unplug the battery and then reconnect it. Keep that in mind; keep it disconnected for around 15 minutes. You will require a little elbow grease under those circumstances.
After that, start the car by inserting the key. Eventually, the data would be cleared and the light would be switched off. Lastly, reconnect the battery once more, then start the ignition.
Monitoring the Gas Tank Lid
Monitoring the gas tank lid to see if you need to reset, it is another crucial part. It’s possible that the gas cap on your GMC Sierra is loose, damaged, lost, emitting fumes, or that gasoline is leaking. Therefore, secure the gas cap.
The component of your engine that ignites the air or fuel mixture in the combustion chamber is often the spark plug. However, damaged plugs will affect your GMC Sierra’s performance level and engine efficiency as well.
Remove the Plug
A possible factor concerning aftermarket parts indicates that the car could also struggle. Meanwhile, OEM parts will benefit you.
Additionally, damaged ignition coils and O2 sensors or a clogged catalytic converter might result from damaged spark plugs or plug cables, which will eventually cost more to fix. Therefore, swap out the old ones with new ones.
Visit Service Center
If you find everything difficult, take your car to the auto shop or service center to detect the problem with your GMC Sierra. Sometimes we use an OBD-II code scanner to detect the issue. Resetting is not a hard and fast job so if you follow our given instructions, hopefully, you won’t have to spend the extra penny to resolve the issue.
Also Read: Fixing P0300 Code Chevy Silverado Issues
Frequently Asked Questions
How do I reset my check engine light manually?
Manually turning off or resetting the check engine light is relatively simple and can be done by performing the following actions:
1. Your key must be in the ignition.
2. Using the scanner, you can detect the issue easily.
3. Then, without removing the battery, turn the ignition on and off for one or two seconds for a hard reset.
4. Do the process 3 to 4 times.
How to reset check engine light without disconnecting battery?
Simply switch the ignition on and off for a few seconds 3 times to reset the engine management light without a battery.
How many miles does it take to reset a check engine light?
In order to get the codes, you should let the light reappear. If the check engine light reappears, drive your car for 30 to 100 miles to ensure it won’t. It does this by allowing the car’s “drive cycle” to restart, which is required for the monitoring systems to have enough time to adjust properly.
How long does it take for a check engine light to clear?
We typically turn off the negative battery cable for around 15 minutes to reset the check engine light. However, after fixing all potential problems, the engine light should never reappear.
Why is my engine light on but nothing seems wrong?
If nothing appears to be wrong with the car but the engine light flashes, you are safe to drive or you should meet with a mechanic to determine if there is a problem with the vehicle. After refilling, if the gas cap is a bit loose, the light could probably turn on. So, keep it secured.
Final Words
So, whenever you notice the check engine light on your GMC Sierra flashing, make sure you identify what’s wrong with the vehicle. We discovered why the light comes on and what codes you will get if the car has troubles.
Plus, if you expect to reset on your own, check the manual idea as well as the other steps like engine starting, ignition turning on plus off, trying the steering wheel, disconnecting the battery, changing parts, monitoring the gas tank lid or extreme level of difficulty should be resolved by the auto shop.
Hello, this is Wesley Shelton, currently working in a car restoration company for over 5 years. Before that, I was a worker at a small car repair shop. As I was a car freak from a young age and worked as a professional for over half a decade, I think I now know pretty much everything about every car and its parts. To establish my name as a professional and help others by sharing my knowledge, I’ve created this website, which I work on whenever I get free time. I hope you’ve enjoyed my informative blog!